If you didn’t have any motivation to fuel your heeded procrastination, we hope our title will help inspire you to roll up your sleeves and get your gear together for a simple paint job this weekend. This Sunday, you’re about to redecorate the dark stained wooden Chester in your bedroom for your wife, and paint it with beautiful strokes to compliment the new console you just bought for the homeroom. Here are some basic Wood Burning Art Tips
Two words – it’s easy! Sure, we don’t expect you to be completely up for the job, since sanding and priming stained wood tends to be a hard chore, but hey, there’ s always a first time. Mentioned below are five steps that tell you how to paint over stained wood like a pro.

How To Paint Over Stained Wood

Remove Any Hardware:

Whether you’re painting your door, window or a dresser, remove all kinds of hardware such as the knobs and latches to avoid hindrance in your paint job.

Cover Up:

While working indoors, you need to cover up the area where you are sitting since you’d probably place your utensils on the carpet or soil the flooring. For best results, try to paint the dark stained wood by covering the area around you with contractor’s paper instead of newspapers or plastic sheets.

Clean The Wood’s Surface:

Pre-finished or hard, stained wood tends to have a coat of lacquer or varnish on it, which makes it necessary to clean the wood of any impurities such as grease, cobwebs, remnants of food and dirt. Cleaning the surface of the wood will also help you to have a second glance towards any remaining pieces of hardware, allowing you to remove any hidden nails, screws or splinters straight away. Mothers are very special in our life, So we got you Homemade Wooden Vase for Mothers Day Gift.
Cleaning dark stained wood before sanding, priming and painting it is also necessary for a fine finish. The paint would either chip off from places where its surface is either hindered by an impurity or won’t stay for long. For best and immediate drying results, cater to Tri-Sodium Phosphate, since it helps to rinse and wash the surface of the dark stained wood with perfection.

Sand The Dark Stained Wood:

Using TSP to clean the dark stained wood earlier might aid in removing the glossy polyurethane or the varnished coat over the surface. Sanding is done in order to allow the wooden surface to adhere to the paint firmly, thus making the paint to respond to the stripped surface adequately and without any hindrance.
Since you’re not catering to raw wood, you need to sand the dark stained wood with a sanding knit paper of fine grit – somewhat between 150 and 200. Sanding will create a great mess which is why covering the surface with contractor paper is necessary and highly recommended. Also, it might create a lot of noise, so grab your earplugs and cover your ears to avoid noise pollution to an extent.

Prime The Surface:

Usually, when people tend to paint a wooden surface without applying a primer first, there are sheens of glossy and flat paint with different levels of radiance all over the wood, which is why this step is highly essential before taking a paint brush to coat your wooden surface. The Kilz and Zinsser 1-2-3 is highly recommended, due to its low odour oil, handiness and shellac glaze.
Primer influences the paint to layer our perfectly, as its chemical bonds help to highlight an amateur paint job to the level of professionalism with pride. Cater to a different brush for a primer and allot a separate day for the chore, since priming takes a lot of time to just dry out. Prime the surface so that the paint job won’t look unreasonable and irregular in several places.

Paint Like A Pro:

Arm yourself with a Wooster 2″ brush to paint the latex paint all over the wooden surface. You can also use a roller or a spray as well, but if you are an amateur, use a brush at first. Only dip the tips of the brush in paint and never sit next to a ventilator or switch on the fan while painting. Avoid dragging your paint brush, or if you really want to quicken your pace, then you can cater to an extender such as Penetrol or Floetrol, that extend open time when in use with oil or latex paints, respectively.
We hope we have convinced you to do this little chore for yourself over the weekend. You may get turned off due to repetitive sanding and priming before painting a coat over the surface, but for best results, this is recommended. We assure you these techniques and products would never let you or your furniture down.